纖維光學互連器件和無源元件檢測

纖維光學互連器件和無源元件檢測項目報價？??解決方案？??檢測周期？??樣品要求？

點 擊 解 答??

GB/T 20171-2006用于工業測量與控制系統的EPA系統結構與通信規范

本標準定義了基于GB/T 15629.3-1995、IEEE Std 802.11、IEEE Std 802.15-2002以及RFC 791、RFC 768和RFC 793等協議的EPA（Ethernet for Plant Automation）系統結構、數據鏈路層協議、應用層服務定義與協議規范以及基于XML的設備描述規范。 本標準適用于工業自動化控制領域。

YD/T 926.3-2009大樓通信綜合布線系統.第3部分:連接硬件和接插軟線技術要求

本部分規定了綜合布線用連接硬件和接插軟線的主要機械物理性能、電氣特性、光學特性和試驗方法。本部分適用于綜合布線用連接硬件和接插軟線。

YD/T 2289.4-2017無線射頻拉遠單元(RRU)用線纜 第4部分:預制成端線纜組件

本部分規定了無線射頻拉遠單元(RRU)用預制成端線纜組件(以下簡稱組件)的產品分類、要求、試驗方法，以及檢驗規則、標志、包裝、運輸和貯存。本部分適用于無線射頻拉遠單元(RRU)用的在工廠中預制成端光纖連接器的光纜組件、預制成端光纖連接器和可能有的電連接器的光電混合纜組件。

IEC 61300-2-4-2019纖維光學互連器件和無源元件. 基本試驗和測量程序. 第2-4部分:試驗. 光纖或者光纜的保持力

The purpose of this part of IEC 61300 is to ensure that the retention or attachment of the fibre, cord or cable in a fibre optic device or an enclosure will withstand tensile loads likely to be applied during normal service.

IEC 61300-2-4 Edition 2.1-2020纖維光學互連器件和無源元件. 基本試驗和測量程序. 第2-4部分:試驗. 光纖或者光纜的保持力

The purpose of this part of IEC 61300 is to ensure that the retention or attachment of the fibre, cord or cable in a fibre optic device or an enclosure will withstand tensile loads likely to be applied during normal service.

IEC 61300-2-9-2017纖維光學互連器件和無源元件.基本試驗和測量規程.第2-9部分:試驗.沖擊試驗

This part of IEC 61300 defines a test method to reveal mechanical weakness and/or degradation of fibre optic devices when subjected to repetitive or non-repetitive mechanical shocks. It simulates infrequent repetitive or non-repetitive shocks likely to be encountered in normal service or during transportation.

IEC 61300-2-10-2021纖維光學互連器件和無源元件. 基本試驗和測量規程. 第2-10部分: 試驗. 抗擠壓和負載

This part of IEC 61300 evaluates the effect of loads which is possible to occur when fibre optic devices are exposed to critical situations such as being stepped on, being run over by vehicle tyres, when an evenly-distributed static load is applied to the top surface of a street cabinet or when a load is applied to a street cabinet's open door.

IEC 61300-2-14-2021纖維光學互連器件和無源元件. 基本試驗和測量規程. 第2-14部分: 試驗. 高光學功率

This part of IEC 61300 describes a procedure for determining the suitability of a fibre optic interconnecting device or a passive component to withstand exposure to the optical power which occurs during its operation.

IEC 61300-2-15-2008纖維光學互連器件和無源元件.基本試驗和測量程序.第2-15部分:試驗.鎖緊機械裝置的扭轉強度

This part of IEC 61300 applies an overload torque to twist-type coupling mechanisms. It isapplicable to threaded or bayonet-twist type coupling mechanisms. It can be used to ensurethat the coupling mechanism of a connector set or connector-device combination will withstandthe torsional loads likely to be applied during normal service.

IEC 61300-2-27-1995纖維光學互連器件和無源元件 基本試驗和測量程序 第2-27部分:試驗 灰塵 層流

Deals with the determination of effects of dust on fibre optic devices.

IEC 61300-2-29-1995纖維光學互連器件和無源元件 基本試驗和測量程序 第2-29部分:試驗 低氣壓

Determines the effect on a fibre optic device of reduced air pressure, such as might be encountered at high altitudes. This procedure is conducted in accordance with IEC 68-2-13, test M.